Loading... Please wait...

Walkera Runner 250 Replacement Frame (Iceytee)

Hover over image to zoom

  • Image 1
  • Image 2
  • Image 3
  • Image 4
  • Image 5
  • Image 6
  • Image 7
  • Image 8
  • Image 9
  • Image 10
  • Image 11
  • Image 12
  • Image 13
  • Image 14
  • Image 15
  • Image 16
  • Image 17
  • Image 18
  • Image 19
  • Image 20
  • Image 21
  • Image 22
  • Image 23
  • Image 24
  • Image 25
  • Image 26
  • Image 27
  • Image 28
  • Image 29
  • Image 30
  • Image 31
  • Image 32
  • Image 33
  • Image 34
  • Image 35
  • Image 36
  • Image 37
  • Image 38
  • Image 39
  • Image 40
Designs by Iceytee
$40.00

 Product Description

A Walkera Runner 250 replacement shell/ body kit.

Take that dusty broken up Runner 250 out of the shoe box in the closet and give it some new life. This body kit is designed to give the Walkera Runner a less bulky stance while being strong and light. When fully assembled this kit gives the frame a weight of 450 grams without the battery. The kit is also designed in such a way that it encases your power distribution board, flight controller, VTX, and receiver to protect it all in the event of a crash. If your original Runner 250 body has been crashed and damaged give this unique frame kit a try. All of the original internal components will fit inside and screw down..  It is very easy to take apart and put back together again which is great for replacing parts quickly.

This can be printed in many color combinations, you choose what you want and I will make it happen. PLEASE BE SURE TO LEAVE ME A NOTE WHEN CHECKING OUT TELLING ME EXACTLY WHAT PARTS YOU WANT IN WHAT COLOR. The color options are black, blue, purple, red, green, grey, yellow, orange, and white. Please let me know what color you would like when you purchase otherwise it will be printed in black by default. This listing will include the body kit parts for the Walkera Runner 250 you see in the last three pictures only.

This listing does not include any hardware or any internal components only the 3D printed body kit. This kit will require 34 M3-8mm screws, 4 M3-18mm screws, 36 M3 nuts, 12M3 washers, and the original screws from the Runner 250 esc's and the camera. These screws can all be purchased at your local Home Depot. Good luck!

Steps for instillation:

  1. 1.   Screw the camera to the main body using a screw on either side.
  2. 2.   Screw the landing gear and bottom frame together using the M3-8mm screws and nuts.
  3. 3.   Screw the 4 arms to the body using the M3-8mm screws, nuts, and washers.
  4. 4.   Screw the antenna holder bridge on the main body using M3-8mm screws and nuts.
  5. 5.   Assemble your power distribution board with the VTX, Flight controller, Receiver, and front and rear lights. Screw it to the top frame with the 2 screw holes on the side.
  6. 6.   Attach and screw in the ESC's and motors.
  7. 7.   Screw the bottom frame with the landing gear to the top frame using the M3-18mm screws and nuts.
  8. 8.   Plug in a battery and you are set to go!

 


logoit2.jpg
This battery is licensed to Great 3D by "Designs by Iceytee", a portion of each sale goes to the designer. 

 Find Similar Products by Category

 Product Reviews

This product hasn't received any reviews yet. Be the first to review this product!

You Recently Viewed...

 

newsletter

Follow us on

Copyright 2017 Plastic-Spider. All Rights Reserved.
Sitemap | BigCommerce Premium Themes by PSDCenter

Click the button below to add the Walkera Runner 250 Replacement Frame (Iceytee) to your wish list.