Loading... Please wait...

Uni mount for transmitter AND receiver (full versions, Transmitter and receiver not included)

Hover over image to zoom

  • Image 1
  • Image 2
  • Image 3
  • Image 4
  • Image 5
  • Image 6
  • Image 7
  • Image 8
Plastic Spider Designs
$12.00

 Product Description

This works with the D4R-II Radio Rx and one of the following 3 Video Tx's (TS5823 200mw Video Tx, TS5828 600mw Video Tx and Eagle FPV200 200mw Video Tx). This may accept other Video Tx's since there seem to be quite a few models using the same circuit board but no other models have yet been confirmed. These are not compatible with the Version 2 frame sold from MRM.

ZMR 250
Uni-Mount Rx/Tx Long (This extends the SMA connector on the Video Tx past the rear edge of the top plate)

Uni-Mount Rx/Tx Short (This aligns the SMA connector with the small hole at the back of the top plate. Note that the hold must be widened for the SMA connector to fit)
 
Also the following improvements have been made to the ZMR 250 Uni-Mounts over the previous version.
1. Thicker Antenna Tube Holders for better strength.
2. Additional support added to the Uni-Mount frame at the rear for better support of the battery strap.
3. Knock-outs for the wiring on the 4 Video Tx's (TS5823, TS5828, Eagle FPV200 and FX718-6 600mw)
4. Rear Standoff Spacers included for all Video Tx versions to help prevent the Uni-Mount frame from cracking in a hard upside down crash.
Great 3d is now carrying these.
5. F/S button on D4R-II aligns with slot in ZMR250 Top Plate.

6. Switches for Channel Selection on the TS5823 and TS5828 align with the cutout in the ZMR250 Top Plate. Circular Cutout on the left side allows access to the button to change channels on the Eagle FPV200. You can change channels on all of these Video Tx's without removing the top plate. The item was designed by pLaStIc sPiDeR and a portion of this sale goes directly to him!

QAV 250

Designed by pLaStIc sPiDeR and based on the same concept as the Uni-Mount for the ZMR250 Quad. This works with the D4R-II Rx and one of the following 4 Video Tx's (TS5823, TS5828, Eagle FPV200 and FX718-6 600mw). This may work with other Video Tx's based on the same circuit board as those mentioned but no other models have been confirmed.
This comes with the Uni-Mount, 2 Standoff Spacers for the rear standoffs, 2 Standoff Caps for the front standoffs, 2 - 1mm plastic washers for the front standoffs that can be used if you are using a Sony Style cam mount.
Note: This does allow access to the Channel selection switches on the TS5823, TS5828 and the channel selection button on the side of the Eagle FPV200 Tx. It also has access to the F/S Button on the Rx. Weight is 8 Grams. Battery clearance with Uni-Mount installed is 24.6mm. A portion of this sale goes directly to the designer. 

Nighthawk 250

Designed by pLaStIc sPiDeR and based on the same concept as the Uni-Mount for the ZMR250 Quad. There are 2 versions, one for 6mm standoffs and one for 5mm standoffs. (if you are not sure which size you have, 3 unworn US Quarters are about 5mm thick, 4 unworn US pennies are about 6mm thick)  This works with the D4R-II Rx and one of the following 4 Video Tx's (TS5823, TS5828, Eagle FPV200 and FX718-6 600mw). This may work with other Video Tx's based on the same circuit board as those mentioned but no other models have been confirmed.

This comes with the Uni-Mount, 2 Standoff Spacers for the rear standoffs, 2 Standoff Caps for the front standoffs, 2 1mm plastic washers for the front standoffs that can be used if you are using a Sony Style cam mount. A portion of this sale goes directly to the designer.

 Find Similar Products by Category

 Product Reviews

  1. Purchase the TPU version!

    Posted by Brian on Feb 16th 2016

    I have the Unimount Long for ZMR250s in ABS, and it fits my E2000 and my X4R-SB without any issues. The issue is that in an upside down crash you can break the back supports of the posts plastic pieces.The mount still holds up but a little disappointing that it did crack with a minor crash, otherwise this is perfect it really cleans up my ZMR250 and is well worth the investment.


  2. Unimount is smooth!

    Posted by Unknown on Dec 19th 2015

    This unimount is one of many great products the great3d.com prints. It really helps clean your zmr 250 build up AND it looks cool! Frsky receiver and 200mw transmitter fit in it perfectly.


  3. Great!

    Posted by Kit Dines on Dec 8th 2015

    I had to cut out some things but those were because of personal preferences. Great product and a very great fit!


  4. awesome product

    Posted by max on Nov 13th 2015

    i got the TPU version. it weighs like 10? grams i think. i got it to protect my antennae, but the holders for the VTx and radio Rx are perfect. i will put one of these on every quad i make.


  5. Great design! FlySky & Eachine fit also!

    Posted by waflet on Oct 6th 2015

    I love smart use of space & clean installs, so this thing (along with most of the rest of the great3d catalog ;) ) is right up my alley. My problem is I had purchased all my electronics before finding this. None of my electronics matched up exactly, but all are very similar, so I gambled on it & ordered anyway.

    The Eachine ET200 (from www.banggood.com) required a little cutting on the top piece of the frame (it is slightly taller). The connector didn't fit & the large, black, round piece between the connector & the antenna are the culprits. A small amount of work with the dremel solved the problem (make sure to wear a mask if your dremeling carbon fiber ;) ) The ET600 would require some cutting on the mount to get it in (it is taller near the antenna so that section would need to be removed), but will probably be ok also.

    I trimmed down the raised section of the RX portion to fit a Fly Sky FS-iA6 & FS-iA6B. The part I had to trim was near the pins (opposite the antennas). There is a raised section that is designed to hold the receiver in place. I trimmed this down flush with the bottom horizontal piece. Both RX's are a tight fit, so I don't think they are going to fall out. I removed the iA6B from its case & removed the shields from the antennas & removed the case from the connector for the PPM cable (to long :/) to get it to fit properly, but I am satisfied with the fit after all that :).


  6. Brilliant

    Posted by MikeF on Aug 24th 2015

    The various choices of style and the design of this mount is extremely well thought out and a perfect fit. The print quality is second to none. Everything fits perfectly.


You Recently Viewed...

 

What's News

  • My Story

    When I turned 18, I started working at a small machine shop creating aluminum …

newsletter

Follow us on

Copyright 2017 Great 3D. All Rights Reserved.
Sitemap | BigCommerce Premium Themes by PSDCenter

Click the button below to add the Uni mount for transmitter AND receiver (full versions, Transmitter and receiver not included) to your wish list.